Firmware:

- For new installations, we changed the default value to 0 (disabled) for the "ext88N IN -> Settings -> Number of 16 input modules" field.
- For new installations, we changed the default value to 0 (disabled) for the "RailCom" checkbox on the "Track Output" screen.
- Major improvements to overall Loconet communication, solving a lot of data loss and wrong / missing feedback messages.

App:
- Added checkbox to reset the dr5000 settings to default when updating the firmware.
- Added the option to change the protocol without an active LAN / WIFI connection.
- Added the option to open the Log screen in full-screen mode.
- Fixed additional issues with the Digitrax UT throttles.
- Fixed issues with setting the language to French.

Firmware:

- Fixed XN + FB bus issues (Firmware 1.6.0 multimaus issue)
- Fixed problems with Digitrax throttle UT4R

App:

- Added option to show feedback monitoring full screen

Firmware:

- Fixed CV read/write bug when using WLANmaus.
- Fixed option to read/write address/CV through the Z21 app.
- Fixed reading/writing CV in Program on Main (POM) mode for Z21 app.
- Fixed the stop / go button functionality within the Z21 app.

App:

- Display the correct switchboard numbers when editing the "Turnout Address" field.
- Added option to open the Drive and Switch screens from the first DR5000 screen.
- Added option to stop the process when reading CV values through a batch.

Firmware:

- Fixed problem with Daisy-Tool not finding hand controllers anymore.

App:

- None.

Firmware:

- LocoNet implementation overhauled to:
* avoid LocoNet getting stuck because of collisions.
* improved timing to respond quicker to slot data requests
- Fixed problem Track Power not turning off when pressing the STOP button.

App:

- Fixed a another crash problem in the drive panel, when clicking on up/down controls.
- Added CV-batch programming/reading based upond a .CSV file

Firmware:

- Current and Temperature measurement working again after a FW update.

App:

- Fixed a crash problem in the drive panel, when running on slow computers or with extreme fast mouse.

Firmware:

- Completed LocoNet implementation of Daisy-II support for Address programming/reading
- Completed LocoNet implementation of IB-V2.0 support for Long Address programming/reading
- Added capability to LocoNet, to let the "Daisy-Tool" work through DR5000 LocoNet COM-Port
- Added capability to LocoNet, to let the "Daisy-Update" work through DR5000 LocoNet COM-Port
- Added configuration option to set the XpressNet Command Staion Type and protocol version
- Added support for MultiMAUS(r) F13-F20 being consistent between multiple Mice.
- Added "loco-steal" (Blinking loco symbol) notification for Mice and LH handcontrollers.
- Added POM-CV read for MultiMAUS (from FW V1-04) and WLANmaus (from FW V1-07) when DR5088RC is setup with DR5000.

App:

- XB+FB Bus properties screen has been changed to add the configuration option for XpressNet Version and Command Station type.
- Installation procedure has been totally overhauled.
Now the installer is selfextracting and supports the update possibility.
No need anymore to first de-install the previous version.

Firmware:

- The whole programming track operation has been thoroughly overhauled and improved.
Regardless of the DR5000 revision it is now possible (at the demo system) to read almost every decoder error-free.
- Daisy II and IB Basic-slave can read and write CVs.
Programming track = read & write, main track = write only (because the Uhl devices can not read POM)
Read address and program (option on Daisy II) are not (yet) supported.
- In the programming area both POM read and write are revised and made faster and more reliable.
With e.g. JMRI you can now read all decoders quickly and conveniently via POM.
- OPC_IMM_PACKET Now this LocoNet command is fully implemented so that e.g. JMRI the so called Signal mast aspects can be sent to so called Extended Accessory Decoders.
- Also for RailCom info the indicated track polarity is now correct, even if "in locomotive address" is selected.

App:

- NEW! Dr.Script is here! After installation you will find Dr.Script.pfd and some examples in the installation folder. Scripting can be found under "Control | Scripting".
- The firmware update is improved, so that the app does not freeze during the flashing.
- Loco drive window contains extra information for RailCom Actual Speed & QoS